Posted in 2020 August-December Mini Catalog, 2020-2021 Stampin' Up! Catalog, beginner stamper, Emboss Powder, Halloween, Punch Art

Stampin’ Up!® Ghostly Halloween Greetings and the Emboss Powder Technique

Hello everyone! It is good to be back home after my road trip to Kentucky. I had a wonderful time visiting my son who is in the Army. I am anxious to start stamping and making cards again!

I have a fun and spooky Punch Art Style card for you today. Punch Art consists of card designs made entirely by using different punches to make images. This is a very simple Punch Art card, where I just turned the Tulip Punch upside down to create the ghost shape. The Halloween stamp set is Hallows Night Magic in the Stampin’ Up! 2020 August-December Mini Catalog. The faces and bows were from the Hippo Happiness stamp set found in the 2020-21 Stampin’ Up! Annual Catalog. I will also go over using Emboss Powder to make the white sentiment on the Basic Black card stock.

Measurements: Basic Black Card Stock (CS): 4 1/4 x 11 inches with a score line at 5 1/2 inches and 3/4 x 4 1/8 inches; Whisper White CS: 4 x 5 1/4 inches (inside) and 2 1/4 x 4 1/2 inches; the black bat design in the Magic In This Night Designer Series Paper (DSP): 4 1/8 x 5 3/8 inches.

Additional supplies: Memento Black ink, Versamark ink, White Stampin’ Emboss Powder and Rhinestone Basic Jewels.

Embossing Supplies Here are the supplies I keep handy when I want to use Emboss Powder. I keep everything in a bag so that when I want to use it, it is all together. Pictured: Versamark ink, Embossing Buddy, White Emboss Powder, spoon, small paint brush and a microfiber cloth. Note: Stampin’ Up! is not currently selling the Embossing Buddy but there are several you can find online, or you can make your own with some tightknit fabric and cornstarch. I have seen instructions for the homemade version online as well.

In order to prepare the 3/4 x 4 1/8 inch Basic Black CS strip for embossing, it is very important to use the Embossing Buddy first to decrease the static and absorb oils from your skin that may be on the paper. Just move the Embossing Buddy firmly from left to right 2 or 3 times. There will be a white residue left behind that we will remove later. Use the Versamark ink and the sentiment “Happy Halloween” to stamp onto the Basic Black CS.

Take care not to touch the stamped sentiment. Hold onto one end of the strip and use the spoon to sprinkle a good amount of the White Emboss Powder onto it. Shake the excess off. Use the paintbrush to remove any of the Emboss Powder that is in the wrong place. Tip: I put my emboss powders in a plastic container because I find it much easier to use than trying to keep the powder in the little jar it comes in. This container has 3 jars of the White Emboss powder in it.

Hold onto one end and use the Heat Tool to apply an even flow of heated air to the Emboss Powder. I move my Heat Tool back and forth to avoid concentrating the heat in one spot and burning the paper. You will suddenly see that the Emboss Powder becomes a bright white and is shiny. Tip: Hold the strip up to a light and ensure that the entire sentiment is white and shiny. If it is still a little dull, apply more heat to that spot.

Allow the Embossed sentiment to cool completely for about 10 minutes, then gently use the microfiber cloth to remove the white residue. Set this aside for the time being.

Lay the 4 x 5 1/4 inch Whisper White CS in a landscape orientation. Use the Memento Black ink to stamp the sentiment “Trick-or-Treat” in the center of the bottom. Turn the card piece to a vertical orientation. Use the Memento to stamp the spider crawling along the side. Set aside.

I usually recommend stamping before cutting. However, I felt it was easier to put the ghost’s faces on after I punched them out. Punch one from each end first, then punch the one in the middle.

Use the Memento ink and the face from the Hippo Happiness stamp set to stamp the faces. I added a little bow to add some variety.

Fold the 4 1/4 x 11 inch Basic Black CS card base at the 5 1/2 inch score line. Use the Bone Folder to get a nice crisp fold. Adhere the black bat design from the Magic in This Night DSP to the card front.

Adhere the stamped 4 x 5 1/4 inch Whisper White CS card piece to the inside.

Stampin’ Up! has white and black Stampin’ Dimensionals. I used the white Dimensionals on the back of the ghosts, and the black Dimensionals on the back of the sentiment. Tip: If you cut the large Dimensionals in half they last longer and you still get a good effect.

Adhere the sentiment and the ghosts as shown.

Time for the Bling! I used the Rhinestone Basic Jewels and the Take Your Pick tool to embellish the background.

And Viola! You have a very fun and spooky card to wish someone a “Happy Halloween”! I know Halloween is going to be different this year. My youngest still wants a costume even though there will not be any house to house Trick-or-Treating. I hope folks can still find a way to have some fun!

Thanks for stopping by today. I feels good to be blogging again.

All of the supplies, except the Embossing Buddy, are available at my online store which you may access HERE, or you may click on any of the photos below to go directly to the store.

Product List

Have a wonderful rest of the week!

Theresa

Author:

Hello, my name is Theresa. I have 4 children and a wonderful husband of 27 years. I am a retired Family Physician who loves creating and crafting, so much so that I became a Stampin' Up! demonstrator. I have been a demonstrator for almost 4 years. Not only do I get to craft, I get to travel and meet new friends from all over the world. Crafting gives me something positive to do and share with others. I love having people over to stamp cards with me. My blog is geared toward the beginner stamper. I want to help others get started stamping in their own home. Come join me!

2 thoughts on “Stampin’ Up!® Ghostly Halloween Greetings and the Emboss Powder Technique

Leave a Reply