This is a very simple and beautiful card. I like to practice an attitude of gratitude. Gratitude has been shown to have positive effects on your overall health, increasing happiness and decreasing depression. This card is fun and straight-forward to make. I did go into more detail to help anyone just starting out stamping. There are 10 tips!
Measurements: Whisper White card stock (CS): 8 1/2 x 5 1/2 inches scored at 4 1/4 inches, 3 x 1 3/4 inches and 2 3/4 x 1 1/4 inches; Terracotta Tile: 5 7/8 x 4 1/8 inches; Gold Glimmer Paper: 5 1/4 x 3/4 inches; Ornate Garden Specialty Designer Series Paper (DSP): 5 1/4 x 2 inches; Old Olive: 3 x 1 1/2 inches. You also need the Ornate Garden Ribbon: 6 1/2 inches for the ribbon around the card and approximately 10 inches to make the bow. Tip #1: Learn how to tie the bow here.
Let’s start stamping! You will stamp the “Thanks” sentiment from the Ornate Thanks Stamp set in Terracotta Tile ink onto the 2 3/4 x 1 1/4 inch piece of Whisper White CS. I stamped a little bit towards the left and above center to allow space for the daisy. Tip #2: This is a Photopolymer stamp (one you can see through). You will need a pad of some sort. I am using the Stampin’ Pierce mat. This is used for Photopolymer stamps to get a better image. You may also use your catalog as a pad if needed.
Stamp the daisy in Memento ink onto the 3 x 1 3/4 inch piece of Whisper White CS. Tip #3: This is a red rubber stamp. You get the best image by stamping on a smooth, firm surface. Note: You can easily see the foam the red rubber rests on. The pink line on top of the foam is the red rubber.
You will need several colors of Stampin’ Blends Alcohol Markers. I started with Light So Saffron alcohol marker (AM) to color the flower petals. Next I used the Dark Daffodil Delight AM to trace the lines in the petals, and make a little ring around the flower center. Tip #4: Practice using the alcohol markers before you do your card. It takes a very light touch to get the ink on the paper, and sometimes it bleeds too far. There is a fine tip and a brush tip. Use the fine tip for small or thin areas and the brush tip for larger areas. Some papers bleed more than others. The Stampin’ Up! Whisper White does not bleed much. It is the best that I have found.
Use the Bronze AM to color the flower center. The Light Old Olive AM is used first for the stem and the leaf.
The reason the markers are called Stampin’ Blends is because you can blend the light and dark shades to make shadows on the image. If you are really good, the image will look 3-D. Tip #5: First apply a thin layer of the Light Old Olive. Then use the fine tip of the Dark Old Olive to trace the line in the leaf and darken the base of the leaf. Finally, use the Light Old Olive to blend the light and dark shades together. Viola!
Fussy cut the daisy cutting as close to the black outline as possible. (“Fussy cut” is the term for cutting an image out with the Paper Snips.)
Tip #6: To get rid of the remaining white on the border, you can go over it with the Basic Black Stampin’ Write marker as shown.
Now it’s time to put everything together. Adhere the Ornate Garden DSP to the bottom of the Terracotta Tile piece, leaving an eighth of an inch border. Then adhere the strip of Gold Glimmer Paper. Tip #7: Try different adhesives to see what you like best. Read all about adhesives here.
Adhere the ribbon to the card front with glue dots. Apply one glue dot to each end of the ribbon. Tip #8: To get the glue dot on the ribbon it is easier to just put the ribbon on top of the glue dot as it is on the roll.
Hold the ribbon in place, flip the card and stick the glue dots down.
Fold the 8 1/2 x 5 1/2 inch Whisper White CS at the 4 1/4 inch score line. This is the card base. Now adhere the decorated card front piece to the front of the Whisper White card base.
Adhere the “Thanks” sentiment to the Old Olive CS piece. We are going to adhere the Thanks piece with Stampin’ Dimensionals. These are little foam pieces with adhesive on both sides. They lift the paper slightly to give dimension to the card.
Tip #9: I usually cut my Stampin’ Dimensionals in half so they last longer. I also cut the part that remains after using all the dimensionals as shown. Apply the Stampin’ Dimensionals to the back of the Thanks piece.
Adhere the Thanks piece to the card front. Now adhere the little daisy we colored and cut out next to the sentiment.
Lastly, add the bow with a glue dot. Tip #9: Apply the glue dot to the back of the bow by placing the bow on the glue dot while it is still on the roll. Gently peel it off of the roll and adhere the bow to the card.
Viola! You have a beautiful thank you card! Tip #10: Now that you have completed the card, send it to someone to let them know how much gratitude you have for them! Too often we make these beautiful cards and then we keep them in a box or something. I am guilty of doing just that, so I have challenged myself to send one card every day for 30 days. I am on day 18. It has been fun and I have gotten wonderful feedback from the folks I have sent cards to!
As always, thank you so much for joining me and reading my blog. I am very grateful to all of you for supporting me in this endeavor!
I am a Stampin’ Up! Demonstrator. If you see anything you would like to purchase, please visit my online store here. If you would like to contact me, follow me on Facebook here or shoot me an email at: Theresastreasures.firstname.lastname@example.org.
Stampin’ Up! products used include: Stamp Set: Ornate Thanks #149471 and Ornate Style #152572; Paper: Whisper White CS #100730, Terracotta Tile CS #150884, Gold Glimmer Paper #146958, Ornate Garden DSP #152488 and Old Olive CS #100702; Ink: Terracotta Tile #150884 and Memento #132708; Clear Blocks: D #118485 and H #118490; Adhesives: Tombow Multipurpose Liquid Glue #110755, Glue Dots #103683 and Stampin’ Dimensionals #104430; Embellishments: Ornate Garden Ribbon Combo Pack #152479.