Hello! Hope you are all doing well and are ready to craft!
I had a customer request that I go over how to use the Stampin’ Emboss Powder to emboss on a card. I’m excited to show you the Emboss Resist technique because it is just magical! This is a very simple card meant to highlight the embossing process.
You will be surprised how simple this lovely card is to make! I used the Stampin’ Up! Forever Fern stamp set for the bunch of leaves and the sentiment.
Measurements: Shimmery White Card Stock (CS): 8 1/2 x 5 1/2 inches with a score line at 4 1/4 inches, 5 1/4 x 4 inches and a 3/4 inch strip measuring at least 3 inches. Tip: I chose the Shimmery White CS because it holds up better to watercoloring than the Whisper White CS. You could also use the Fluid 100 Watercolor Paper for the 5 1/4 x 4 inch piece.
Embossing. The first step is to use an embossing static remover powder. (Stampin’ Up! had one called the Embossing Buddy but unfortunately it retired. Information on where to get one is at the end of the blog.)
The second step is to use Versamark ink which is a high viscosity ink so that the Stampin’ Emboss Powder will adhere to it. Tip: I ink the larger stamps upside down to be sure to get the ink evenly distributed.
Carefully stamp the bunch of leaves image onto your 5 1/4 x 4 inch Shimmery White CS in Versamark ink. It will be hard to see. Take care not to touch the Versamark ink on the card because it will smear. Stamp the sentiment “HELLO” in Versamark ink onto the 3/4 inch strip of Shimmery White CS.
The third step is to apply the emboss powder to the image stamped in Versamark ink. I used White Stampin’ Emboss Powder. I use a spoon to put enough of the emboss powder to cover the image. Tip: I keep my Stampin’ Emboss Powders in a plastic container so that it is easier to use. You can just pour the powder from the jar onto the image and catch the extra powder with a piece of paper. Then pour the powder back into the jar.
I use the spoon to tap the paper and remove any excess emboss powder. You can see the image somewhat. Notice that the Stampin’ Emboss Powder is dull. When you use the Heat Tool it will become shiny.
I use a small paint brush to remove emboss powder that is on by mistake before heating it.
For this step I am using Shaded Spruce CS to better show you the process. The fourth and final step is to use the Heat Tool to melt the Stampin’ Emboss Powder. I usually let the Heat Tool run for 10 seconds before waving it in front of the paper. I keep the Heat Tool moving about 1-2 inches away from the paper. You will see a change in the emboss powder as it melts. For the White Stampin’ Emboss Powder you will see it turn from dull to shiny. The leaves on the left are before heating, on the right after heating.
Now we can watercolor! I used the Aqua Painter that is retired. There are new Water Painters in the new Stampin’ Up! 2020-2021 Annual Catalog. I just haven’t gotten them yet. They work the same. I applied a layer of water to the paper. Using Old Olive ink I started at the top of the image using wide brush strokes. Tip: To get the ink on the lid of the ink pad, squeeze the pad in the center.
I used Shaded Spruce ink for the bottom part of the bunch of leaves, blending the two ink colors in the middle. Dab the image with a paper towel to remove excess ink over the embossed image. I used the Shaded Spruce alone for the watercolor wash behind the sentiment. Tip: Squeeze the Watercolor Painter brush onto a paper towel before changing colors to remove the ink. Be sure to clean it when you are done watercoloring.
Adhere the embossed piece to the 8 1/2 x 5 1/2 inch Shimmery White CS after you have folded it at the 4 1/4 inch score line. Trim the sentiment and apply it to the card front with Stampin’ Dimensionals.
Now for some Bling! The Gold Glitter Enamel Dots are perfect for dressing up this simple card.
Apply an odd number of dots for best results. Tip: Apply the Gold Glitter Enamel Dots using the Take Your Pick tool. It makes transferring the dots from the acetate sheet to the card much easier.
And Viola! there you have a beautiful card to say “HELLO” to someone special.
I hope you enjoyed learning to emboss. If you already knew the magic of embossing, I hope you will try this card. Have a most wonderful day and find some time to craft today!
There is a special for the month of June when you join my Stamping Gems team! For $99 you not only get to choose $125 of product for your Starter Kit, you also get to choose a free bundle of your choice. The bundle can be one stamp set with a punch, or one stamp set with dies. Email me at email@example.com if you are interested or have any questions.
The static remover powder can be bought at any online scrapbook store. One that I found is at Scrapbook Pal. Click here to purchase.
Thank you so much! Have a wonderful day!